The One Fit Check That Matters
Before you order XPEL Armor Mudflap Protection, confirm your Cybertruck is wearing mudflaps bought from the Tesla store. The film is cut for those factory mudflaps only. Third-party clones vary in size and fit, so the cutouts will not line up reliably.
If you already have aftermarket mudflaps, this kit is not the right match. If you are still deciding on mudflaps, start with the Tesla OEM set so the armor film can do its job.
What the Mudflap Armor Kit Includes
- Xpel Armor Mudflap Protection (only for Tesla OEM Mudflaps): Tough decals for each of the factory mudflaps, made with ultra-tough XPEL Armor Protection Film. You get a matched set for the OEM mudflaps rather than a universal sheet you have to trim.

Xpel Armor Mudflap Protection (only for Tesla OEM Mudflaps) - Xpel Armor Mudflap Protection (only for Tesla OEM Mudflaps): Precision cutout that requires no heat gun or special skills. The install is designed to be approachable for a DIY owner without professional tools.
- Xpel Armor Mudflap Protection (only for Tesla OEM Mudflaps): Double-sided squeegee included. You have the basic tool needed to press the film down and work out air.
How to Install the Armor Film on OEM Mudflaps
The supplied instructions and video are the best source for exact steps. Use the sequence below as a practical framework, and follow the official guidance for any detail not covered here.
- Clean the mudflap surface: Remove dirt and road film so the adhesive can bond. A clean, dry surface is the baseline for any film install.
- Test-fit the cutout before peeling: Hold the decal against the OEM mudflap to confirm orientation and coverage. The precision cutout is shaped for the Tesla mudflap, so it should align without trimming.
- Peel and place: Apply the film to the mudflap, starting from one edge and working across to avoid trapping air.
- Press with the squeegee: Use the included double-sided squeegee to press the film down firmly and smooth out bubbles.
- Check edges and repeat on the other side: Make sure edges are seated, then install the second decal on the opposite mudflap.
Caring for the Textured Satin Black Finish
XPEL Armor has a textured satin black appearance similar to a bed liner, and it is resistant to UV, grease, tar, dirt, and oil. That makes it a practical match for mudflaps that see road spray and grime.
For routine care, wash with normal car shampoo and rinse. Avoid abrasive polishes or aggressive scrubbing that could change the texture. The film is designed to be easy to remove and replace, so if a section becomes damaged you can swap it without replacing the mudflap.
Where This Kit Fits Into Your Cybertruck Armor Plan
The mudflap decals complement other XPEL Armor pieces, especially rockers and wheel flares. If you are building out cybertruck paint protection accessories, this is a small addition that completes the lower-body look.
- Match the finish: The textured satin black ties in with other XPEL Armor parts for a consistent lower-body appearance.
- Protect a high-wear area: Mudflaps take direct hits from road debris, so film there helps preserve the surface underneath.
- Keep expectations realistic: This is a decal set for the mudflaps, not a replacement mudflap or a full rocker kit. Confirm you have the OEM mudflaps first.
Product Details at a Glance
- Xpel Armor Mudflap Protection (only for Tesla OEM Mudflaps): Thickness: 23mil (0.6mm). A substantial film thickness for a mudflap application.
- Xpel Armor Mudflap Protection (only for Tesla OEM Mudflaps): Appearance: Textured Satin Black (similar to a bed liner). Sets the visual expectation and care approach.
- Xpel Armor Mudflap Protection (only for Tesla OEM Mudflaps): Entirely made in Texas, USA. Useful for buyers who prioritize domestic manufacturing.


