العودة إلى المدونة
أدلة إرشادية 2026-11-17 Abstract Ocean | Tesla & Rivian Accessories | A Texas Co. est 0 مشاهدة

Rivian R1T Door Sill PPF: Install & Care Guide

Rivian R1T Door Sill PPF: Install & Care Guide

How to install pre-cut door sill PPF on your Rivian R1T, pick the right Gen 1 or Gen 2 cutout, and care for the film so it keeps blocking scuffs.

Why the R1T door sills need film

The Rivian R1T has no step to help you climb in, so the painted door entry area takes the full brunt of dirty shoes, heels, and whatever else comes through the door. That makes it one of the most vulnerable sections of paintwork on the truck, and a scratch-prone zone for people and pets going in and out.

Pre-cut door sill PPF puts a clear sacrificial layer over that paint. The Door Sill Protection Film (PPF) for Rivian R1T covers all four door entry areas with 100% clear film that is almost invisible once installed, so the truck looks stock while the paint underneath stays shielded.

Install the pre-cut sills in 20 minutes

The kit is built for DIY: four precision-cut PPF pieces, one per door, with no heat gun or special skills required. Work one door at a time and follow the supplied installation instructions and video for the exact sequence.

  1. Confirm your R1T generation: The film is offered for Gen 1 (2022-2024) and Gen 2 (2024-), so check your model year before ordering. The cutouts are precision-made for each generation.
  2. Mix the slip solution: The kit includes a spray bottle with slip concentrate; add water as directed. Wet the sill and the adhesive side of the film so you can position it before it grabs.
  3. Apply and squeegee: Place the cutout on the door entry area, then use the included squeegee to push the slip solution out from under the film, working toward the edges.
  4. Repeat on all four doors: Each door gets its own piece. Finish one before moving to the next so you can keep track of the cutouts.

What comes in the R1T door sill kit

Pick the right generation before you peel

The Door Sill Protection Film for the R1T is sold in two variants: Gen 1 (2022-2024) and Gen 2 (2024-). The cutouts are precision-made, so ordering the wrong generation is the most likely way to end up with film that does not sit correctly. Check your truck's model year and generation first.

If you are unsure which generation you have, confirm it before ordering rather than trying to stretch a cutout into place. The supplied information does not include a measurement guide for distinguishing the two, so use your vehicle documentation to verify.

Care that keeps the film clear

The supplied information does not include a detailed care schedule, so keep it simple and avoid anything that could lift the edges. These habits protect the film without guesswork.

  • Wash gently around the edges: Avoid high-pressure blasting directly at the film's edges, which can lift the adhesive over time.
  • Skip abrasive cleaners: Use normal car wash soap and a soft mitt rather than abrasive pads or strong solvents on the film.
  • Remove and replace when worn: The film is designed to be easy to remove and replace, so if a sill gets badly scuffed you can refresh that piece rather than living with it.

Where this fits in your R1T protection plan

Door sills are one of several high-contact zones on the R1T. If you are already adding PPF to the bumper lip or front fenders, the sills are a low-cost addition that addresses a different kind of damage: foot traffic rather than road debris. The kit is made in Texas, USA, and priced at USD 31.99 in the catalog.

The supplied information does not state a warranty period or a cure time for the film, so treat those as questions to confirm with the seller rather than assumptions.

مقالات ذات صلة

Customer Service
الرئيسية
المنتجات
السلة
الملف الشخصي