Back to Blog
Tips & Care 2026-11-17 Abstract Ocean | Tesla & Rivian Accessories | A Texas Co. est 0 views

Rivian R1T Truck Bed Side PPF: Coverage and DIY Install Tips

Rivian R1T Truck Bed Side PPF: Coverage and DIY Install Tips

Protect your R1T bed sides from loading scrapes with pre-cut clear PPF. Compare partial vs full coverage, prep the panel, and install without a heat gun.

Why the R1T bed sides need film

The sides of the Rivian R1T truck bed take a beating every time you load or unload gear. Clear protection film (PPF) adds a sacrificial layer that absorbs scuffs and stains while staying virtually invisible. The Truck Bed Side Clear Protection Film for Rivian R1T is pre-cut for both driver and passenger sides, so you can shield the paint without a custom wrap shop.

This guide covers the two coverage options, what comes in the kit, and a practical install sequence based on the supplied product information. It also flags where the supplied details leave room for your own judgment.

What the kit includes

  • Truck Bed Side Clear Protection Film (PPF) for Rivian R1T: 2 x PPF cutouts made for DIY install (one for Passenger and one for Driver side), plus a spray bottle with soap (just add water) and a squeegee. You get both sides and the basic tools, so no separate slip solution or squeegee purchase is needed for the install.
    Truck Bed Side Clear Protection Film (PPF) for Rivian R1T
    Truck Bed Side Clear Protection Film (PPF) for Rivian R1T
  • Truck Bed Side Clear Protection Film (PPF) for Rivian R1T: Made with ultra premium self-healing, stain resistant paint protection film that is 100% clear and virtually invisible once installed. The film protects against loading scrapes while preserving the factory paint appearance.

Partial vs full coverage: which cutout fits your use

The kit comes in two sizes. The partial wrap covers only the outermost area of the truck bed side. The full wrap covers the entire panel without the C pillars, but it does not wrap around the edges; it runs to the end of the panel on each side except for a few-millimeter gap at the far rear near the tail lights, which is left to make installation easier.

  • Partial Coverage: Covers the outer most area of the bed side. Easier to position and a sensible choice if you mainly want protection where loads slide in and out.
  • Full Coverage: Covers the entire panel without the C pillars. Provides more protection but is significantly more difficult to install due to the curves around the tail lights. The supplied information recommends prior PPF experience for this option.

A sensible install sequence for the pre-cut film

The film is precision cut and does not require a heat gun or special skills, but the full wrap is a large piece that needs two people for positioning. Work in a clean, shaded area and keep the panel and your hands free of grit.

  1. 1. Confirm your coverage choice and side: Lay out the driver and passenger cutouts and check that you have the partial or full version you ordered. The full wrap is noticeably larger and more curved at the tail-light end.
  2. 2. Clean the bed side thoroughly: Wash and dry the panel so no dust or grease remains. The supplied instructions do not list a specific cleaner, so use a gentle car-wash soap and rinse well.
  3. 3. Mix the slip solution: Fill the included spray bottle with water and add the supplied soap as directed. This solution lets you reposition the film before squeegeeing.
  4. 4. Position with a helper: For the full wrap, have a second person hold the film while you align the top edge and the tail-light gap. The partial wrap is smaller but still benefits from a second set of hands.
  5. 5. Squeegee out the solution: Starting from the center, use the included squeegee to push air and water toward the edges. Work methodically to avoid trapping bubbles.
  6. 6. Check edges and let it settle: The full wrap intentionally leaves a few-millimeter gap at the far rear near the tail lights. Do not stretch the film to close that gap; it is designed for easier installation.

What the supplied information does not settle

The supplied product details do not specify a cure time, a recommended installation temperature, or a maximum time before you can wash the truck after installation. They also do not list a specific soap-to-water ratio beyond 'just add water.' For those details, follow the installation instructions and video included with the kit rather than guessing.

The film is described as self-healing and stain resistant, but the supplied information does not state how long self-healing takes or which contaminants it resists. Treat those as general PPF characteristics rather than precise promises for this cutout.

Product at a glance

Related Articles

Customer Service
Home
Products
Cart
Profile